Click Here for AirGunHome.com Main Page
Argentina Australia Belgium Canada Chile Denmark France Germany Greece India
Italy Mexico New Zealand Netherlands Norway Russian Federation South Africa Spain Turkey United Kingdom United States
AirGunHome.com: THE Worldwide Airgun Forum


RifleScope-Shop.com Store Logo
Air Gun Home Forum Index Register FAQ Memberlist Search

Air Gun Home Forum Index » Rifles » Crosman 1077 Assembly Help
Post new topic  Reply to topic View previous topic :: View next topic 
Crosman 1077 Assembly Help 
PostPosted: Sun Mar 07, 2010 8:05 pm Reply with quote
Funkyman
New Member
New Member
Joined: 07 Mar 2010
Posts: 4
I had to take apart the 1077 to do some barrel maintenance. So I did. I took it apart according to the directions on this website. At the step where you remove the cover to see all the insides of the gun, I took the cover off and a piece fell out. Later I took a spring off but I dont know how to put it back on. I know where it goes though. These two parts that I dont know where to put are a V like spring and a small cylindrical piece. I have pictures to help.






I the second picture, the object on the right is the cylindrical piece. The one on the left is the v spring. In the first picture, the v spring is with the pieces it was around. Where does the small cylindrical piece go and how do I put the v spring back in. Notice on the v spring that it has two ends sticking down, one longer one shorter. Please specify which end goes where. Also notify me if you can see the ppictures as I am not sure that I did it right.
View user's profile Send private message
 
PostPosted: Sun Mar 07, 2010 8:35 pm Reply with quote
packrat
Senior Member
Senior Member
Joined: 16 Nov 2009
Posts: 882
Location: Out in the woods...Ellabell, GA.
Have you had a look at Crosman's parts diagram for that particular gun??? Lot of times it can be a big help Mr. Green Mr. Green

_________________
HEY !! This getting old thing is NOT for sissies...
View user's profile Send private message Visit poster's website
 
PostPosted: Sun Mar 07, 2010 10:22 pm Reply with quote
Funkyman
New Member
New Member
Joined: 07 Mar 2010
Posts: 4
I have looked at it but it is not a close up picture of the spot I want to see and when I enlarge the image, it gets all fuzzy.
View user's profile Send private message
 
PostPosted: Mon Mar 08, 2010 2:56 pm Reply with quote
AirGunEric
Site Admin
Site Admin
Joined: 20 Jan 2007
Posts: 6519
Location: "Out There"
You can leave it out. It's purpose is to block an accidental release of the hammer if the rifle is dropped or jarred extremely.

If this doesn't suit you, the spring goes in, with the spring ends facing upward at the top-most part of the housing, the pin goes through the spring ring and the hole in the tab and the tab goes towards the bottom of the receiver/housing- both spring arms are on the same/upper side of the tab. Once you figure it out, it's not so bad, but without an example sitting next to you, it could be a problem.

_________________
`

I'd say "I care."

But I'd be lying.


Canadian Airgun Supplier: http://www.scopesandammo.com/storefront
View user's profile Send private message Visit poster's website
 
PostPosted: Mon Mar 08, 2010 6:18 pm Reply with quote
Funkyman
New Member
New Member
Joined: 07 Mar 2010
Posts: 4
I got the spring, pin, and tab in easy enough but after I had everything in, I pulled the trigger and the pin swung out and prevented the hammer from going fully forward. Is this right? I might actually just leave it out. And, where does the short round piece in picture 2 on the right go?
View user's profile Send private message
 
PostPosted: Mon Mar 08, 2010 11:03 pm Reply with quote
AirGunEric
Site Admin
Site Admin
Joined: 20 Jan 2007
Posts: 6519
Location: "Out There"
You have the tab facing the wrong way- thus why it is sticking on the hammer.

I believe, and it's hard to tell from the picture, the sleeve is the one that should go over the pin on the hammer that the trigger lever rides on- reducing friction and wear between the two.

_________________
`

I'd say "I care."

But I'd be lying.


Canadian Airgun Supplier: http://www.scopesandammo.com/storefront
View user's profile Send private message Visit poster's website
 
PostPosted: Tue Mar 09, 2010 5:56 pm Reply with quote
Funkyman
New Member
New Member
Joined: 07 Mar 2010
Posts: 4
After many tries of getting the springs to stay down and putting the barrel into position, I finally got it. Thanks for all the help.
View user's profile Send private message
 
PostPosted: Thu Apr 15, 2010 5:08 pm Reply with quote
userng999
New Member
New Member
Joined: 15 Apr 2010
Posts: 1
Yes that cylindrical piece goes on the thin pin on the hammer. Without it that pin will wear out fairly quickly.
View user's profile Send private message
Crosman 1077 Assembly Help 
  Air Gun Home Forum Index » Rifles
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
All times are GMT - 5 Hours  
Page 1 of 1  

  
  
 Post new topic  Reply to topic  

Note: If you are seeing "Please enter your username and password to log in." Your browser cookies have been reset
or you need to register to access the topic in question. Use the 'Register' button near the top left of this page.


Click Here for AirGunHome.com Main Page


Powered by phpBB © 2001-2004 phpBB Group
Partial Styling Supplied by Vjacheslav Trushkin Themes Database.