Click Here for AirGunHome.com Main Page
Argentina Australia Belgium Canada Chile Denmark France Germany Greece India
Italy Mexico New Zealand Netherlands Norway Russian Federation South Africa Spain Turkey United Kingdom United States
AirGunHome.com: THE Worldwide Airgun Forum


AirGunSeals.com Main Page Link
Air Gun Home Forum Index Register FAQ Memberlist Search

Air Gun Home Forum Index » Airgun Smithing » Marader Stock Sealant
Post new topic  Reply to topic View previous topic :: View next topic 
Marader Stock Sealant 
PostPosted: Sun Feb 14, 2010 8:57 pm Reply with quote
shamu25
New Member
New Member
Joined: 14 Feb 2010
Posts: 4
Location: Grand Rapids, MI
Just bought a new Mrod and wondering what to put on the stock to seal, add a polish and make the checkering stand out. It is a beautiful piece of wood but seems a bit dull and dry and needs to be spruced up a bit. Thanks
View user's profile Send private message
 
PostPosted: Sun Feb 14, 2010 9:20 pm Reply with quote
fritz
Silver Status Member
Silver Status Member
Joined: 25 Nov 2008
Posts: 2444
Location: New Jersey- outside of Philadelphia
Sniper should be able to give you great advice. Check out this recent thread about his latest refinish job.

http://www.airgunhome.com/agforum/viewtopic.php?t=4732

Nice job, Sniper.

_________________
"I never set out to be wierd, it was always everyone else who called me it" -Frank Zappa

Speed is impressive, accuracy is deadly.

It's not that I'm not a people person, it's just that I'm not a stupid people person.
View user's profile Send private message AIM Address MSN Messenger
Re: Marader Stock Sealant 
PostPosted: Sat Feb 27, 2010 7:11 pm Reply with quote
sniper
Silver Status Member
Silver Status Member
Joined: 28 Nov 2008
Posts: 3752
Location: Star, Idaho
shamu25 wrote:
Just bought a new Mrod and wondering what to put on the stock to seal, add a polish and make the checkering stand out. It is a beautiful piece of wood but seems a bit dull and dry and needs to be spruced up a bit. Thanks


i have an mrod. bitchen gun eh?

i've done nothing to the stock yet, however
slavia likes to use paste wax.
if memory serves my right he does a rub down (very light)
with super fine steel wool and rubbing compound
then applies 2 coats of wax. same as what you would do
to an auto paint job.
his method is on my to-do list.

it's not that the finish is dull it is just finished with a very low
sheen (gloss) clear. a little more dull than satin which i like.

or, you can give it a very light sand with 400 grit
and shoot a coat of oil based polyurethane on it.
if you do-DO NOT OVER SAND THE HIGH SPOTS!!
for the checkering go to the paint store and buy a fine
grit "sanding sponge".

_________________
I believe in gun control,
If there's a gun around I
want to be controlling it.......
View user's profile Send private message
 
PostPosted: Sun Feb 28, 2010 12:02 am Reply with quote
AirGunEric
Site Admin
Site Admin
Joined: 20 Jan 2007
Posts: 6931
Location: "Out There"
Crosman actually makes those stocks in-house. They told me what they were, now I can't remember, Beech or something...

_________________
`

I'd say "I care."

But I'd be lying.


Canadian Airgun Supplier: http://www.scopesandammo.com/storefront
View user's profile Send private message Visit poster's website
 
PostPosted: Sun Feb 28, 2010 10:19 am Reply with quote
Slavia
Moderator
Moderator
Joined: 31 Mar 2008
Posts: 4382
Location: Waseca, Minnesota, USA
Quote:
slavia likes to use paste wax.
if memory serves my right he does a rub down (very light)
with super fine steel wool and rubbing compound
then applies 2 coats of wax. same as what you would do
to an auto paint job.


Quite correct. There are also a couple of products you might consider - Birchwood Casey Tru-Oil or Min-Wax Wipe On Poly. Both go on with a clean cloth, applying just enough to make the surface look "wet." Then you rub them out and use paste wax. The poly is clear; the Tru-Oil imparts a slight amber hue. My Slavia 631 was, as you described, "dull and dry." Three coats of Tru-Oil plus the paste wax fixed it right up.

Tru-Oil is of the same family of finishes as tung oil and boiled linseed oil, in that they react with oxygen to cure. Tru-Oil has been heat treated to make it cure faster - you can get a couple of coats on in a day. Tung oil or boiled linseed oil can take several days for a single coat. Poly is a resin in a volatile vehicle, and that vehicle evaporates pretty quickly (leaving the resin behind).

You don't want finish to pool in the grooves of the checkering, so I would pat it out with a cloth. Don't wipe sideways, as the sharp checkering will tear out cloth fibers and embed them in the finish. Likewise don't use a paper towel, since the fibers are very short and detach easily. An old toothbrush will keep the paste wax from building up in the checkering.

_________________
¡Listo! ¡Apunte! ¡Fuego!
View user's profile Send private message
Stock finish 
PostPosted: Sun Feb 28, 2010 12:36 pm Reply with quote
shamu25
New Member
New Member
Joined: 14 Feb 2010
Posts: 4
Location: Grand Rapids, MI
Thanks guys...this is exactly what I have been looking for
Blessings
Shamu
View user's profile Send private message
Re: Marader Stock Sealant 
PostPosted: Sun Feb 28, 2010 6:17 pm Reply with quote
donec
Senior Member
Senior Member
Joined: 19 Dec 2009
Posts: 836
Location: central Texas Pflugerville area
sniper wrote:
shoot a coat of oil based polyurethane on it.
What do you mean shoot a coat? Do you mean spray? If so what do you use to spray with, is it like car paint that needs special pressure or just any sprayer will do like an airbrush?
View user's profile Send private message Visit poster's website
 
PostPosted: Sun Feb 28, 2010 7:14 pm Reply with quote
sniper
Silver Status Member
Silver Status Member
Joined: 28 Nov 2008
Posts: 3752
Location: Star, Idaho
yes spray. slang painters term. i use ZAR fast dry in a spray can.
i can run liquid through my gravity fed conventional gun
(with my air compressor) cut with a little naptha
or either of my commercial grade graco airless sprayers
but that would be for a big job (cabinets etc) for a stock a spray can is all you need.

they're around $8/can. 1 can does 2 stocks @ 6-8 coats per stock.

_________________
I believe in gun control,
If there's a gun around I
want to be controlling it.......
View user's profile Send private message
Marader Stock Sealant 
  Air Gun Home Forum Index » Airgun Smithing
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
All times are GMT - 5 Hours  
Page 1 of 1  

  
  
 Post new topic  Reply to topic  

Note: If you are seeing "Please enter your username and password to log in." Your browser cookies have been reset
or you need to register to access the topic in question. Use the 'Register' button near the top left of this page.


Click Here for AirGunHome.com Main Page


Powered by phpBB © 2001-2004 phpBB Group
Partial Styling Supplied by Vjacheslav Trushkin Themes Database.