Click Here for AirGunHome.com Main Page
Argentina Australia Belgium Canada Chile Denmark France Germany Greece India
Italy Mexico New Zealand Netherlands Norway Russian Federation South Africa Spain Turkey United Kingdom United States
AirGunHome.com: THE Worldwide Airgun Forum


AirGunSeals.com Main Page Link
Air Gun Home Forum Index Register FAQ Memberlist Search

Air Gun Home Forum Index » Airgun Smithing » NPSS barrel shroud..............
Post new topic  Reply to topic View previous topic :: View next topic 
NPSS barrel shroud.............. 
PostPosted: Sat Jan 02, 2010 12:09 pm Reply with quote
packrat
Senior Member
Senior Member
Joined: 16 Nov 2009
Posts: 882
Location: Out in the woods...Ellabell, GA.
Since Crosman has not as yet put up a parts diagram on their website(?), I need to ask here...how would I go about removing the and cap and barrel shroud from NPSS? Lokks like the cap might just slip on, thereby holding the bull barrel looking shroud in place. Would like to know for sure to avoid doing any damage...thanks.......

_________________
HEY !! This getting old thing is NOT for sissies...
View user's profile Send private message Visit poster's website
 
PostPosted: Sat Jan 02, 2010 12:53 pm Reply with quote
broommaster2000
Moderator
Moderator
Joined: 10 Mar 2007
Posts: 5712
Location: City of Groningen, Groningen, The Netherlands
Crowbar? Razz

Aren't these clipped on or something?

_________________
BIG GAP
View user's profile Send private message
 
PostPosted: Sat Jan 02, 2010 3:37 pm Reply with quote
packrat
Senior Member
Senior Member
Joined: 16 Nov 2009
Posts: 882
Location: Out in the woods...Ellabell, GA.
I looked at it. can't tell, only thing I can figure is that it slips on with a tight fit (unlike my ex, but don't get me started on THAT Laughing Laughing )

_________________
HEY !! This getting old thing is NOT for sissies...
View user's profile Send private message Visit poster's website
 
PostPosted: Sat Jan 02, 2010 4:40 pm Reply with quote
kanyon
Silver Status Member
Silver Status Member
Joined: 09 Aug 2008
Posts: 1582
Location: New Zealand
packrat wrote:
I looked at it. can't tell, only thing I can figure is that it slips on with a tight fit (unlike my ex, but don't get me started on THAT Laughing Laughing )



PMSL Shocked


Now to the gun.... Laughing
The end cap is most lightly pressed on....
If you heat it i may com free....

NOW...To heat it with out damage....
Place the end of the barrel/end cap in boiling water
for a while....ie hold it in a jug/kettel for 5/10mins
while it is boiling..
If its a allo or plastic cap it will exspand faster & more
than the steel barrel...

Pete
View user's profile Send private message MSN Messenger
 
PostPosted: Sat Jan 02, 2010 5:58 pm Reply with quote
packrat
Senior Member
Senior Member
Joined: 16 Nov 2009
Posts: 882
Location: Out in the woods...Ellabell, GA.
It screws on...the whole thing is one piece and just slides over the barrel..muzzle end is threaded (female)...end of barrel is threaded (male) so I guess I'm not gonna go to the trouble.....was thinking about shortening the barrel waaaaay too much trouble though , the way it's set up .

_________________
HEY !! This getting old thing is NOT for sissies...
View user's profile Send private message Visit poster's website
NPSS barrel shroud.............. 
  Air Gun Home Forum Index » Airgun Smithing
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
All times are GMT - 5 Hours  
Page 1 of 1  

  
  
 Post new topic  Reply to topic  

Note: If you are seeing "Please enter your username and password to log in." Your browser cookies have been reset
or you need to register to access the topic in question. Use the 'Register' button near the top left of this page.


Click Here for AirGunHome.com Main Page


Powered by phpBB © 2001-2004 phpBB Group
Partial Styling Supplied by Vjacheslav Trushkin Themes Database.