 |  | | | |  | |  |  | NPSS barrel shroud.............. |  | |  |  | |
 Posted: Sat Jan 02, 2010 12:09 pm |
 |
|
| packrat |
| Senior Member |
|
|
| Joined: 16 Nov 2009 |
| Posts: 882 |
| Location: Out in the woods...Ellabell, GA. |
|
|
|
| Since Crosman has not as yet put up a parts diagram on their website(?), I need to ask here...how would I go about removing the and cap and barrel shroud from NPSS? Lokks like the cap might just slip on, thereby holding the bull barrel looking shroud in place. Would like to know for sure to avoid doing any damage...thanks....... |
|
_________________
HEY !! This getting old thing is NOT for sissies... |
|
|
|
|
|
| |  |  | | | |  |  |
| | | | | | | | | | | | | | |
| Posted: Sat Jan 02, 2010 12:53 pm |
|
|
| broommaster2000 |
| Moderator |
 |
|
| Joined: 10 Mar 2007 |
| Posts: 5714 |
| Location: City of Groningen, Groningen, The Netherlands |
|
|
|
Crowbar? 
Aren't these clipped on or something? |
|
|
|
|
|
|
| | | | | | | | |
| | | | | | | | | | | | | | |
| Posted: Sat Jan 02, 2010 3:37 pm |
|
|
| packrat |
| Senior Member |
|
|
| Joined: 16 Nov 2009 |
| Posts: 882 |
| Location: Out in the woods...Ellabell, GA. |
|
|
|
I looked at it. can't tell, only thing I can figure is that it slips on with a tight fit (unlike my ex, but don't get me started on THAT  ) |
|
_________________
HEY !! This getting old thing is NOT for sissies... |
|
|
|
|
|
| | | | | | | | |
| | | | | | | | | | | | | | |
| Posted: Sat Jan 02, 2010 4:40 pm |
|
|
| kanyon |
| Silver Status Member |
|
|
| Joined: 09 Aug 2008 |
| Posts: 1582 |
| Location: New Zealand |
|
|
|
| packrat wrote: |
| I looked at it. can't tell, only thing I can figure is that it slips on with a tight fit (unlike my ex, but don't get me started on THAT ) |
PMSL 
Now to the gun....
The end cap is most lightly pressed on....
If you heat it i may com free....
NOW...To heat it with out damage....
Place the end of the barrel/end cap in boiling water
for a while....ie hold it in a jug/kettel for 5/10mins
while it is boiling..
If its a allo or plastic cap it will exspand faster & more
than the steel barrel...
Pete |
|
|
|
|
|
|
| | | | | | | | |
| | | | | | | | | | | | | | |
| Posted: Sat Jan 02, 2010 5:58 pm |
|
|
| packrat |
| Senior Member |
|
|
| Joined: 16 Nov 2009 |
| Posts: 882 |
| Location: Out in the woods...Ellabell, GA. |
|
|
|
| It screws on...the whole thing is one piece and just slides over the barrel..muzzle end is threaded (female)...end of barrel is threaded (male) so I guess I'm not gonna go to the trouble.....was thinking about shortening the barrel waaaaay too much trouble though , the way it's set up . |
|
_________________
HEY !! This getting old thing is NOT for sissies... |
|
|
|
|
|
| | | | | | | | |
Note: If you are seeing "Please enter your username and password to log in." Your browser cookies have been reset
or you need to register to access the topic in question. Use the 'Register' button near the top left of this page.
|
