 |  | | | |  |  |  |  | Recrowning my Benjamin Discovery Help |  | |  |  |  |
Posted: Thu May 07, 2015 12:50 pm |
|
|
| Ledbetter122 |
| Member |

|
 |
| Joined: 24 Feb 2015 |
| Posts: 30 |
|
|
|
 |
Since I have my gun apart (I was detuning my disco to get 750 fps and I drilled 1 size too big.......because I'm impatient....)
I was going to look at my crown and see if it needed to be re-crowned. I'm seeing a bunch of Slotted Brass Screw with lapping compound used to crowning.
I was wondering couldn't I just use one my 5.56 bullets with compound?
If not what size screw head do I need exactly (my gun is .22 cal), they say slightly larger, but that not specific enough for me to try it myself.
Sorry for the numerous questions I have on this thread, I just want to learn everything I can |
|
|
 |
 |
|
|
|  |  |  | | | |  |  |
 |  | | | |  |  |  |  | |  | |  |  |  |
Posted: Sun May 10, 2015 3:21 pm |
|
|
| AirGunEric |
| Site Admin |

 |
 |
| Joined: 20 Jan 2007 |
| Posts: 6931 |
| Location: "Out There" |
|
|
 |
| You can't use the same size as th bore of the barrel- you wouldn't be crowning anything. Likewise, using something made of lead will do nothing. |
|
|
 |
 |
|
|
|  |  |  | | | |  |  |
 |  | | | |  |  |  |  | |  | |  |  |  |
Posted: Sun May 10, 2015 6:23 pm |
|
|
| Mentolio |
| Veteran Member |

|
 |
| Joined: 02 Jun 2013 |
| Posts: 207 |
| Location: Sadly, New Jersey |
|
|
 |
Here are the screws I use: the larger is a 1/4-20 with a head diameter a little under 1/2 inch. This one I used to do my Disco .22. The smaller one is, err...smaller, and I use it for .177 barrels. Head diameter a bit larger than 1/4 inch. Both made of brass, and found at the Home Depot (soft plastic packages hanging on hooks in hardware). Hope this helps!
 |
|
|
 |
 |
|
|
|  |  |  | | | |  |  |
 |  | | | |  |  |  |  | |  | |  |  |  |
Posted: Tue May 12, 2015 9:21 am |
|
|
| Ledbetter122 |
| Member |

|
 |
| Joined: 24 Feb 2015 |
| Posts: 30 |
|
|
|
 |
Alright I did it, With success I used a 6mm Brass Slot Screw (6mm being the head size not the screw length) and some Valve Grinding Compound (from Auto-Zone)
Thanks for your input guys
This ended up making my groups go from 1/2-1" groups at 20 Yards to almost pellet on pellet.
My buddy actually wanted me to do the same thing to his gun also (Benjamin Titan .177) and it made his groups shrink from a Silver Dollar to a Penny at 20 yards, but go figure his scope blew out 5 shots after the gun actually started shooting good.
We actually thought for a minute that I messed his barrel up (Lol), but we took the scope off and kinda barrel aimed the gun and got penny groups again. |
|
|
 |
 |
|
|
|  |  |  | | | |  |  |
 |  | | | |  |  |  |  | |  | |  |  |  |
Posted: Tue May 12, 2015 3:50 pm |
|
|
| Mentolio |
| Veteran Member |

|
 |
| Joined: 02 Jun 2013 |
| Posts: 207 |
| Location: Sadly, New Jersey |
|
|
 |
| That's awesome (improved groups...not your buddy's scope dying)! Isn't it amazing how much of a difference a new crown can make? It kinda makes me mad that some manufacturers don't take the (10 minutes or so?) time necessary to make sure something so vital is done properly. I'm glad to worked out for you. |
|
|
 |
 |
|
|
|  |  |  | | | |  |  |
Note: If you are seeing "Please enter your username and password to log in." Your browser cookies have been reset
or you need to register to access the topic in question. Use the 'Register' button near the top left of this page.
|