 |  | | | |  |  |  |  | Does Crosman Pre fill airguns before they ship |  | |  |  |  |
Posted: Thu Apr 30, 2015 12:04 pm |
|
|
| Ledbetter122 |
| Member |

|
 |
| Joined: 24 Feb 2015 |
| Posts: 30 |
|
|
|
 |
I had ordered a Benjamin Discovery a couple weeks ago from Wal-Mart, and IT WAS A USED ONE. The reason I know is because the valve seal was leaking. When I cleaned my gun and fired it a few times it shot out oil between where the bolt housing meets the air tube.
Also a big red flag was Teflon Tape around the Gauge Threads, and I read a forum somewhere that said you should not need teflon tape since the O-Ring prevents any air from even getting to the threads.
Alright, now onto why I'm asking this question. I had returned the gun that I described above and ordered a new one, Which came in the mail today. I took it out of the box and inspected the gun (looking for scratches on the mount to see if a scope had been previously mounted).
I then looked at the gauge and it read 500-600 PSI, I called Crosman with the question and the answer I got was that they do put some air, so the valve will close so people who use pumps will have an easier time filling it up.
Is this really normal (my last one came empty, but then again it was used)?
I'm just very skeptical since my adventure with airguns has been a really rocky road. |
|
|
 |
 |
|
|
|  |  |  | | | |  |  |
 |  | | | |  |  |  |  | Re: Does Crosman Pre fill airguns before they ship |  | |  |  |  |
Posted: Thu Apr 30, 2015 12:46 pm |
|
|
| Bob La Londe |
| Veteran Member |

 |
 |
| Joined: 05 Nov 2014 |
| Posts: 146 |
| Location: Yuma, Az |
|
|
 |
| Ledbetter122 wrote: |
I had ordered a Benjamin Discovery a couple weeks ago from Wal-Mart, and IT WAS A USED ONE. The reason I know is because the valve seal was leaking. When I cleaned my gun and fired it a few times it shot out oil between where the bolt housing meets the air tube.
Also a big red flag was Teflon Tape around the Gauge Threads, and I read a forum somewhere that said you should not need teflon tape since the O-Ring prevents any air from even getting to the threads.
Alright, now onto why I'm asking this question. I had returned the gun that I described above and ordered a new one, Which came in the mail today. I took it out of the box and inspected the gun (looking for scratches on the mount to see if a scope had been previously mounted).
I then looked at the gauge and it read 500-600 PSI, I called Crosman with the question and the answer I got was that they do put some air, so the valve will close so people who use pumps will have an easier time filling it up.
Is this really normal (my last one came empty, but then again it was used)?
I'm just very skeptical since my adventure with airguns has been a really rocky road. |
I don't know if its normal since both of my Crosman PCPs were refurbs (both came with some air in them), but it makes sense to have a couple hundred PSI in them to keep the valves seated. |
|
|
 |
 |
|
|
|  |  |  | | | |  |  |
 |  | | | |  |  |  |  | |  | |  |  |  |
Posted: Thu Apr 30, 2015 7:19 pm |
|
|
| AirGunEric |
| Site Admin |

 |
 |
| Joined: 20 Jan 2007 |
| Posts: 6931 |
| Location: "Out There" |
|
|
 |
| There is always some air in their PCP guns- don't know if it's a consistent amount- but most often I have seen a couple hundred psi. |
|
|
 |
 |
|
|
|  |  |  | | | |  |  |
 |  | | | |  |  |  |  | |  | |  |  |  |
Posted: Sat May 02, 2015 6:39 am |
|
|
| Mentolio |
| Veteran Member |

|
 |
| Joined: 02 Jun 2013 |
| Posts: 207 |
| Location: Sadly, New Jersey |
|
|
 |
| Both my Mrod and Disco came with a few hundred psi. Good bet that it's not leaking if if does, right? |
|
|
 |
 |
|
|
|  |  |  | | | |  |  |
Note: If you are seeing "Please enter your username and password to log in." Your browser cookies have been reset
or you need to register to access the topic in question. Use the 'Register' button near the top left of this page.
|