 |  | | | |  |  |  |  | Hello from Little Rock |  | |  |  |  |
Posted: Mon Nov 09, 2015 1:41 pm |
|
|
| jblackfish |
| New Member |

 |
 |
| Joined: 09 Nov 2015 |
| Posts: 4 |
| Location: Little Rock, AR |
|
|
 |
Hi, I'm new to this forum. I currently own a Beeman P3, Beeman R7 (.20) and Diana RWS LP8. I like them all for target and light hunting. Actually the P3 is a little light for hunting (400fps) IMO but it may be my skill that's lacking.
(I removed the comment about the loose air gun screws on the HW90 - I think I may have confused the the information on that rifle. I should get it today so I'll know more in a few days and re-ask the question in the proper forum if needed.)
Anyway, I hope to enjoy the forum, learn more about the sport of air gun shooting and how to improve the quality of my activity in the sport. |
|
Last edited by jblackfish on Tue Nov 10, 2015 9:28 am; edited 2 times in total _________________ What goes around comes around |
|
 |
 |
|
|
|  |  |  | | | |  |  |
 |  | | | |  |  |  |  | |  | |  |  |  |
Posted: Mon Nov 09, 2015 8:54 pm |
|
|
| Slavia |
| Moderator |

 |
 |
| Joined: 31 Mar 2008 |
| Posts: 4382 |
| Location: Waseca, Minnesota, USA |
|
|
 |
Welcome to the forum! When people talk about loose airgun screws they are usually talking about the stock mounting screws - two in the fore end and one back by the trigger.
Be sure you're using blue Loctite. It will prevent the screws from vibrating loose, but the screws can still be removed with tool pressure. The red stuff is permanent, and it will take a torch to get the red stuff to let go.
A single drop of blue on the screws' threads is all it takes. |
|
_________________
¡Listo! ¡Apunte! ¡Fuego! |
|
 |
 |
|
|
|  |  |  | | | |  |  |
 |  | | | |  |  |  |  | |  | |  |  |  |
Posted: Tue Nov 10, 2015 9:32 am |
|
|
| jblackfish |
| New Member |

 |
 |
| Joined: 09 Nov 2015 |
| Posts: 4 |
| Location: Little Rock, AR |
|
|
 |
| Slavia wrote: |
Welcome to the forum! When people talk about loose airgun screws they are usually talking about the stock mounting screws - two in the fore end and one back by the trigger.
Be sure you're using blue Loctite. It will prevent the screws from vibrating loose, but the screws can still be removed with tool pressure. The red stuff is permanent, and it will take a torch to get the red stuff to let go.
A single drop of blue on the screws' threads is all it takes. |
Thanks for the welcome, Slavia. And thanks for the help with the loose screw question. I'm familiar with the blue Loctite from using it on other to secure a screw or two on other guns in the past - I know to NOT use the red where a permanent set is not required from past experience.  |
|
_________________ What goes around comes around |
|
 |
 |
|
|
|  |  |  | | | |  |  |
 |  | | | |  |  |  |  | |  | |  |  |  |
Posted: Tue Nov 10, 2015 3:14 pm |
|
|
| Slavia |
| Moderator |

 |
 |
| Joined: 31 Mar 2008 |
| Posts: 4382 |
| Location: Waseca, Minnesota, USA |
|
|
 |
|
_________________
¡Listo! ¡Apunte! ¡Fuego! |
|
 |
 |
|
|
|  |  |  | | | |  |  |
Note: If you are seeing "Please enter your username and password to log in." Your browser cookies have been reset
or you need to register to access the topic in question. Use the 'Register' button near the top left of this page.
|