 |  | | | |  |  |  |  | is there a drop in ported discovery valve on the market |  | |  |  |  |
Posted: Thu Jul 02, 2015 11:13 am |
|
|
| Bowmann94 |
| New Member |

|
 |
| Joined: 02 Jul 2015 |
| Posts: 6 |
| Location: Benson mn |
|
|
 |
| Hi I'm new to the forum and to modifying air guns, but I'm mechanically inclined and used to modding firearms. So I've always wanted a pcp air rifle, and thanks to a big bonus from work I just ordered a .22 discovery. My inner tinkering mind is going nuts with the possibilities I can build the easy mods like a power adjuster, and a stronger hammer spring,but I really want to get my fpe in the high 40s or better. But I don't have the tooling to do serious valve mods. are there any drop in ported valves and or transfer tubes available? |
|
|
 |
 |
|
|
|  |  |  | | | |  |  |
 |  | | | |  |  |  |  | |  | |  |  |  |
Posted: Thu Jul 02, 2015 2:39 pm |
|
|
| rsterne |
| Moderator |

 |
 |
| Joined: 15 Jan 2008 |
| Posts: 2998 |
| Location: Coalmont, BC |
|
|
 |
Norm at DiscosRUs has one, no idea how good, but it does over 40 FPE no problem, and uses Crosman transfer ports, which will limit it.... The valve I did for the Millennium Pumper is being made and sold by Mike at RatSniperSlugs, and uses larger transfer ports, good for up to .30 cal.... Both use 10-32 screws to allow a 3000 psi fill.... You will also need a PRod gauge port to allow more airflow into the valve.... If you intend to use more than a 2000 psi fill, you will also need a stronger hammer spring, and eventually the gun will get impossible to cock if you go too far.... However, 40 FPE is within reach in .22 cal.... Aim to launch the most accurate pellet in the 18-21 gr. range in your gun in the mid 900s, which you can do without going crazy on the fill pressure or hammer spring, and you'll have a dynamite combination with either valve....
Bob |
|
_________________ Dominion Marksman Silver Shield - 5890 x 6000 in 1976, and downhill ever since!
Airsonal: Too many to count! |
|
 |
 |
|
|
|  |  |  | | | |  |  |
 |  | | | |  |  |  |  | |  | |  |  |  |
Posted: Thu Jul 02, 2015 3:01 pm |
|
|
| Bowmann94 |
| New Member |

|
 |
| Joined: 02 Jul 2015 |
| Posts: 6 |
| Location: Benson mn |
|
|
 |
| Thanks I'll check them both out. for the valves would I have to drill and tap the gun to take 10-32 vrs whatever is stock? Not that that would be hard just I'm waiting on gun to ship so I've yet to see anything but pictures. Much to my wife's dismay I can't stand to leave anything I buy stock, so I figured I'd plan it out now. |
|
|
 |
 |
|
|
|  |  |  | | | |  |  |
 |  | | | |  |  |  |  | |  | |  |  |  |
Posted: Thu Jul 02, 2015 3:27 pm |
|
|
| Bowmann94 |
| New Member |

|
 |
| Joined: 02 Jul 2015 |
| Posts: 6 |
| Location: Benson mn |
|
|
 |
| Just looked at the discorus valve, that's exactly what I had in mind thanks. So with ether valve will I need p-rod ports or just mikes valve? Thanks again I can't wait to get started on this gun. I do a lot of pest control for friends in Minneapolis and this gun should work great for that. |
|
|
 |
 |
|
|
|  |  |  | | | |  |  |
Note: If you are seeing "Please enter your username and password to log in." Your browser cookies have been reset
or you need to register to access the topic in question. Use the 'Register' button near the top left of this page.
|