Click Here for AirGunHome.com Main Page
Argentina Australia Belgium Canada Chile Denmark France Germany Greece India
Italy Mexico New Zealand Netherlands Norway Russian Federation South Africa Spain Turkey United Kingdom United States
AirGunHome.com: THE Worldwide Airgun Forum


AirGunSeals.com Main Page Link
Air Gun Home Forum Index Register FAQ Memberlist Search

Air Gun Home Forum Index » Rifles » Crosman 140, modding and weaknesses?
Post new topic  Reply to topic View previous topic :: View next topic 
Crosman 140, modding and weaknesses? 
PostPosted: Wed Jan 14, 2015 9:57 pm Reply with quote
DavidSaunders
Veteran Member
Veteran Member
Joined: 05 Mar 2014
Posts: 140
For those that have or have had a Crosman 140:

For a Crosman 140 with Timmy MAC-1's flat top piston head installed I have the following questions about power and reliability.

What are the weak points? Pivots, Quad seal, Piston, Breach, Check,etc, what is known to fail?

What would likely be the effects of reducing the valve volume?

What would likely be the effects of increasing the valve volume?

How much can the valve outlet be bored out safely?

Can the transfer port be bored out safely?

Will decreasing the mass of the hammer have a benefit (as it is a blow open, so overcoming inertia)?

Will changing the strength of the valve closing spring have any positive effect?

Is it true that the bolt is a flow through design?

Is the bolt long enough to consistently push the pellet past the transfer port?

What trigger mods can be done to improve the trigger pull (I know there is not much to work with here)?

What are the sizes of all of the O-Rings and the Quad Seal?

Is there anything else that I am not thinking to ask that I should know?

Thank you.
View user's profile Send private message
Crosman 140 
PostPosted: Fri Jan 23, 2015 6:34 am Reply with quote
JonahStark
New Member
New Member
Joined: 23 Jan 2015
Posts: 11
Location: Bluffton, Texas
I'm rebuilding a Crosman 140 that is missing the Valve Pin 140A-036. It is probably 1/4" diameter, but I need the length to make a new one.

Anybody able to measure it for me?
lroach1@hotmail.com
View user's profile Send private message
Re: Crosman 140 
PostPosted: Fri Jan 23, 2015 4:43 pm Reply with quote
lampy
Veteran Member
Veteran Member
Joined: 04 Aug 2012
Posts: 297
Location: South Dakota
JonahStark wrote:
I'm rebuilding a Crosman 140 that is missing the Valve Pin 140A-036. It is probably 1/4" diameter, but I need the length to make a new one.

Anybody able to measure it for me?
lroach1@hotmail.com


I looked through my parts stash and the pin I have measures 0.2" diameter and it is 0.8" long. Hope this helps.

_________________
Too many projects to list.
View user's profile Send private message
Pin 
PostPosted: Fri Jan 23, 2015 5:00 pm Reply with quote
JonahStark
New Member
New Member
Joined: 23 Jan 2015
Posts: 11
Location: Bluffton, Texas
Thanks, appreciate it.
View user's profile Send private message
Re: Crosman 140 
PostPosted: Fri Jan 23, 2015 9:16 pm Reply with quote
DavidSaunders
Veteran Member
Veteran Member
Joined: 05 Mar 2014
Posts: 140
lampy wrote:
JonahStark wrote:
I'm rebuilding a Crosman 140 that is missing the Valve Pin 140A-036. It is probably 1/4" diameter, but I need the length to make a new one.

Anybody able to measure it for me?
lroach1@hotmail.com


I looked through my parts stash and the pin I have measures 0.2" diameter and it is 0.8" long. Hope this helps.

Thank you for that. I am still waiting for my Crosman 140 to get to me, I had thought this week though things did not go quite to plan.

I am using the time I would be shooting, resealing, and improving my 140 if it were here to do more research on the 140. So every bit of info helps, no matter how small. I am adding those dimensions to my notes.
View user's profile Send private message
 
PostPosted: Fri Jan 23, 2015 10:38 pm Reply with quote
lampy
Veteran Member
Veteran Member
Joined: 04 Aug 2012
Posts: 297
Location: South Dakota
It is on a different forum but this is a link to a 760 build I did a while back, the early 760 has the same "self cocking" valve as the 140 / 1400.
http://www.airgunone.com/forums/showthread.php?t=5864

_________________
Too many projects to list.
View user's profile Send private message
Pin 
PostPosted: Sat Jan 24, 2015 6:59 am Reply with quote
JonahStark
New Member
New Member
Joined: 23 Jan 2015
Posts: 11
Location: Bluffton, Texas
Thanks lampy.
I have to leave today for a funeral and won't have a chance to work on the 140 until Tuesday.

David, is the pin you measured the Valve pin or the split pin used to hold the pump arm? .8" seems long, but like I said, can't work on guns now due to my daughter-in-laws mother passing away.

I have really enjoyed these last 8 months since I got on the kick of finding non-working airguns and bringing them back to life. Don't know what I'll do with 33 working air guns, but it's fun taking turns shooting them. Crosman 140, BSA Mercury and Crosman 1077 all three needing something to get them working properly.
View user's profile Send private message
quad ring 
PostPosted: Sat Jan 24, 2015 8:22 am Reply with quote
JonahStark
New Member
New Member
Joined: 23 Jan 2015
Posts: 11
Location: Bluffton, Texas
lampy,
saw on the other forum that you may have the quad rings available. What do you want for one?
Jonah
lroach1@hotmail.com
View user's profile Send private message
Re: Pin 
PostPosted: Sat Jan 24, 2015 4:52 pm Reply with quote
lampy
Veteran Member
Veteran Member
Joined: 04 Aug 2012
Posts: 297
Location: South Dakota
JonahStark wrote:

David, is the pin you measured the Valve pin or the split pin used to hold the pump arm? .8" seems long


I guess I'm not 100% sure the pin is the same one you need, it was in with other 140/ 1400 valve parts. (I'm sure it's not the pump arm pin though) The pin fit through the part 140A024 that was in the same drawer so I assumed the pin I measured was part #140A036. Hopefully someone else can confirm the dimensions.

_________________
Too many projects to list.
View user's profile Send private message
Re: quad ring 
PostPosted: Sat Jan 24, 2015 5:06 pm Reply with quote
lampy
Veteran Member
Veteran Member
Joined: 04 Aug 2012
Posts: 297
Location: South Dakota
JonahStark wrote:
lampy,
saw on the other forum that you may have the quad rings available. What do you want for one?
Jonah
lroach1@hotmail.com


That post was made quite a while ago, I may have a quad ring left, (I'm not sure) if I do I'm keeping it in case I stumble across another project with that style of valve. I have bought from The Oring store in the past and been happy with them http://www.theoringstore.com/index.php?main_page=index&cPath=367_111

_________________
Too many projects to list.
View user's profile Send private message
 
PostPosted: Sat Jan 24, 2015 6:33 pm Reply with quote
AirGunEric
Site Admin
Site Admin
Joined: 20 Jan 2007
Posts: 6931
Location: "Out There"
Looking at the piston head mentioned- it only appears to be a Delrin (plastic) replacement piece with a urethane o-ring, and the advantage (performance-wise) would be almost nothing (space in front of o-ring looks about the same as airspace around regular/stock piston seal when installed/compressed.

So my question really is- why go with this part instead of replacing the seal on the factory piston?

_________________
`

I'd say "I care."

But I'd be lying.


Canadian Airgun Supplier: http://www.scopesandammo.com/storefront
View user's profile Send private message Visit poster's website
Quad ring 
PostPosted: Sat Jan 24, 2015 7:35 pm Reply with quote
JonahStark
New Member
New Member
Joined: 23 Jan 2015
Posts: 11
Location: Bluffton, Texas
Lampy, don't blame for wanting to keep the last ring. I would also, thanks.
View user's profile Send private message
 
PostPosted: Sat Jan 24, 2015 7:53 pm Reply with quote
lampy
Veteran Member
Veteran Member
Joined: 04 Aug 2012
Posts: 297
Location: South Dakota
I agree Eric, I remember the piston being a flat top design. So I don't see much of a gain to be had going with an aftermarket design. Replacement pump seals are still available from JG airguns, Baker Airguns and I'm sure there are others.

_________________
Too many projects to list.
View user's profile Send private message
Crosman 140, modding and weaknesses? 
  Air Gun Home Forum Index » Rifles
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
All times are GMT - 5 Hours  
Page 1 of 1  

  
  
 Post new topic  Reply to topic  

Note: If you are seeing "Please enter your username and password to log in." Your browser cookies have been reset
or you need to register to access the topic in question. Use the 'Register' button near the top left of this page.


Click Here for AirGunHome.com Main Page


Powered by phpBB © 2001-2004 phpBB Group
Partial Styling Supplied by Vjacheslav Trushkin Themes Database.