 |  | | | |  | |  |  | Reseal a Crosman Mark 2 |  | |  |  | |
 Posted: Tue May 14, 2013 8:33 pm |
 |
|
| RacerX |
| Member |
|
|
| Joined: 08 May 2013 |
| Posts: 32 |
| Location: Maryland |
|
|
|
This is an old c02 pistol I have had for a long time. I never shot it much and I tried to put a cartridge in it and it leaked out all over the place. Mostly from the screw in puncture piece in the grip.
Luck for me I found a reseal kit on E Bay for 22 dollars.
So here it goes.
 |
|
_________________
Worlds fastest 250cc four stroke. |
|
|
|
|
|
| |  |  | | | |  |  |
| | | | | | | | | | | | | | |
| Posted: Wed May 15, 2013 9:32 am |
|
|
| RacerX |
| Member |
|
|
| Joined: 08 May 2013 |
| Posts: 32 |
| Location: Maryland |
|
|
|
I have hit my first snag. I can't get the piece inside that the plunger goes through to unscrew. I made a screwdriver that fit perfectly. But it is tight. I will soak it for a while and try again.
Fearing damage I will not try very hard. If it will not move I will put in the seals I can. Then look for a gun smith or another piercing piece. I never give up once I start something. But as a watchmaker and motorcycle engine builder. I don't play or make things worse. |
|
_________________
Worlds fastest 250cc four stroke. |
|
|
|
|
|
| | | | | | | | |
| | | | | | | | | | | | | | |
| Posted: Wed May 15, 2013 9:45 pm |
|
|
| AirGunEric |
| Site Admin |
 |
|
| Joined: 20 Jan 2007 |
| Posts: 6908 |
| Location: "Out There" |
|
|
|
"piece inside that the plunger goes through to unscrew" -?
What do you mean by this? The "plunger" in the cap that you press to puncture the Co2 caplet, or something in/around the valve? |
|
|
|
|
|
|
| | | | | | | | |
| | | | | | | | | | | | | | |
| Posted: Thu May 16, 2013 6:44 am |
|
|
| RacerX |
| Member |
|
|
| Joined: 08 May 2013 |
| Posts: 32 |
| Location: Maryland |
|
|
|
Sorry I don't know what to call these parts. The par that the co2 cartridge pushes agenced.
 |
|
_________________
Worlds fastest 250cc four stroke. |
|
|
|
|
|
| | | | | | | | |
| | | | | | | | | | | | | | |
| Posted: Thu May 16, 2013 1:12 pm |
|
|
| RacerX |
| Member |
|
|
| Joined: 08 May 2013 |
| Posts: 32 |
| Location: Maryland |
|
|
|
After soaking the parts overnight in PB Blaster. I made a special screwdriver. It was wide at the tip. Then narrow so as not to touch the threads. I also made up a fixture to hold the piece still.
It worked!!!
Now I can proceed.
 |
|
_________________
Worlds fastest 250cc four stroke. |
|
|
|
|
|
| | | | | | | | |
| | | | | | | | | | | | | | |
| Posted: Thu May 16, 2013 5:58 pm |
|
|
| RacerX |
| Member |
|
|
| Joined: 08 May 2013 |
| Posts: 32 |
| Location: Maryland |
|
|
|
I put the seals in the piercing piece. The other o rings go on the bolt mechanism. One on the ram and one looks like it goes in the top part in front of the handle.
I removed the grips to clean ad to try to open the top breach part. After removing the grips. I noticed the safety lever is broken. I don't recal it ever having a safety. So now I need some parts.
Are there parts available. I can make one. But don't have that much time.
 |
|
_________________
Worlds fastest 250cc four stroke. |
|
|
|
|
|
| | | | | | | | |
| | | | | | | | | | | | | | |
| Posted: Thu May 16, 2013 9:31 pm |
|
|
| AirGunEric |
| Site Admin |
|
|
| Joined: 20 Jan 2007 |
| Posts: 6908 |
| Location: "Out There" |
|
|
|
| There are not alot of reproduction Mark I/II parts out there- if you have the skills- you will probably be further ahead making one yourself. |
|
|
|
|
|
|
| | | | | | | | |
Note: If you are seeing "Please enter your username and password to log in." Your browser cookies have been reset
or you need to register to access the topic in question. Use the 'Register' button near the top left of this page.
|
