 |  | | | |  | |  |  | Marauder O rings |  | |  |  | |
 Posted: Fri Feb 18, 2011 9:45 pm |
 |
|
| domer_pyle |
| Senior Member |
|
|
| Joined: 17 Sep 2009 |
| Posts: 523 |
|
|
|
|
| Anybody know the size of the breech o ring for a .25 M-rod? The one that's actually inside the barrel. Jammed it up and shot it out and now it's nowhere to be found! |
|
|
|
|
|
|
| |  |  | | | |  |  |
| | | | | | | | | | | | | | |
| Posted: Fri Feb 18, 2011 10:04 pm |
|
|
| rsterne |
| Moderator |
 |
|
| Joined: 15 Jan 2008 |
| Posts: 2998 |
| Location: Coalmont, BC |
|
|
|
It should be 1/4" ID x 3/8"OD x 1/16" thickness (nominal).... that is a number 010....
Bob |
|
_________________
Dominion Marksman Silver Shield - 5890 x 6000 in 1976, and downhill ever since!
Airsonal: Too many to count! |
|
|
|
|
|
| | | | | | | | |
| | | | | | | | | | | | | | |
| Posted: Fri Feb 18, 2011 11:38 pm |
|
|
| jimineecricket |
| Member |
|
|
| Joined: 03 Feb 2011 |
| Posts: 83 |
| Location: beaver dam |
|
|
|
| rsterne wrote: |
It should be 1/4" ID x 3/8"OD x 1/16" thickness (nominal).... that is a number 010....
Bob |
Cool any special instructions on putting in the new one? |
|
|
|
|
|
|
| | | | | | | | |
| | | | | | | | | | | | | | |
| Posted: Fri Feb 18, 2011 11:55 pm |
|
|
| rsterne |
| Moderator |
|
|
| Joined: 15 Jan 2008 |
| Posts: 2998 |
| Location: Coalmont, BC |
|
|
|
I don't have a Marauder, but here is a part diagram:
http://www.crosman.com/pdf/manuals/2563%20EVP%20and%20PL.pdf
It looks like the O-ring fits between the barrel (against the end of it) and the shroud mount.... I would assume that you must remove both from the breech to replace it.... unless you can fold it over and manage to get it back into the groove from the breech....
Bob |
|
_________________
Dominion Marksman Silver Shield - 5890 x 6000 in 1976, and downhill ever since!
Airsonal: Too many to count! |
|
|
|
|
|
| | | | | | | | |
| | | | | | | | | | | | | | |
| Posted: Sat Feb 19, 2011 4:08 am |
|
|
| domer_pyle |
| Senior Member |
|
|
| Joined: 17 Sep 2009 |
| Posts: 523 |
|
|
|
|
| Haha, sorry again about that! |
|
|
|
|
|
|
| | | | | | | | |
| | | | | | | | | | | | | | |
| Posted: Sat Feb 19, 2011 3:14 pm |
|
|
| jimineecricket |
| Member |
|
|
| Joined: 03 Feb 2011 |
| Posts: 83 |
| Location: beaver dam |
|
|
|
| domer_pyle wrote: |
| Haha, sorry again about that! |
Ya you better be you gonna have to go to maraurder shootin school before you touch my gun again!!! Now you owe me $2.50 :0 plus pain and SUFFERING!!! ;-D |
|
|
|
|
|
|
| | | | | | | | |
| | | | | | | | | | | | | | |
| Posted: Sat Feb 19, 2011 3:16 pm |
|
|
| jimineecricket |
| Member |
|
|
| Joined: 03 Feb 2011 |
| Posts: 83 |
| Location: beaver dam |
|
|
|
| rsterne wrote: |
I don't have a Marauder, but here is a part diagram:
http://www.crosman.com/pdf/manuals/2563%20EVP%20and%20PL.pdf
It looks like the O-ring fits between the barrel (against the end of it) and the shroud mount.... I would assume that you must remove both from the breech to replace it.... unless you can fold it over and manage to get it back into the groove from the breech....
Bob |
Hey thanks a bunch Bob That helped alot! I got the orings form the farm and barn in 6 pack  They fit great. I was able to fingal one in with out diasassmbely!! How sweet is that. Anyhow you were right on the money with size! Proast to you my friend! |
|
|
|
|
|
|
| | | | | | | | |
| | | | | | | | | | | | | | |
| Posted: Sun Feb 20, 2011 1:34 pm |
|
|
| domer_pyle |
| Senior Member |
|
|
| Joined: 17 Sep 2009 |
| Posts: 523 |
|
|
|
|
| I'll just wait til you get that single shot tray, kinda hard to botch that up! |
|
|
|
|
|
|
| | | | | | | | |
| | | | | | | | | | | | | | |
| Posted: Sun Feb 20, 2011 10:55 pm |
|
|
| donwalk |
| Veteran Member |
|
|
| Joined: 09 Jun 2009 |
| Posts: 247 |
| Location: republik of kaliphornia |
|
|
|
| #5 in home depot plumbing |
|
_________________
never squat while wearing spurs...will rogers |
|
|
|
|
|
| | | | | | | | |
Note: If you are seeing "Please enter your username and password to log in." Your browser cookies have been reset
or you need to register to access the topic in question. Use the 'Register' button near the top left of this page.
|
