 |  | | | |  |  |  |  | Accuair Force 1100 |  | |  |  |  |
Posted: Fri Jan 22, 2010 10:18 pm |
|
|
| donec |
| Senior Member |

|
 |
| Joined: 19 Dec 2009 |
| Posts: 836 |
| Location: central Texas Pflugerville area |
|
|
 |
| Just picked up a Accuair Force 1100 (Turkey made) with a Simmons 4x32 scope for $49.00 from Academy and the barrel looks like it droops but with the adjustable sights it is pretty accurate. No real grouping measurements yet. It had too much oil on it and in the barrel, but all the screws were very tight. The first shot (even after it was cleaned) sounded like a high powered powder rifle but soon settled down. The trigger is quite nice much nicer than on my Storm short first stage and crisp light second stage. Cocking it is harder than the Storm. The scope seems to have too much parallax error. After just a few shots the screws on the scope started getting loose so it will probably need to have some blue Loctite if we decide to use a scope. |
|
|
 |
 |
|
|
|  |  |  | | | |  |  |
 |  | | | |  |  |  |  | |  | |  |  |  |
Posted: Sat Jan 23, 2010 4:34 pm |
|
|
| joek |
| Member |

 |
 |
| Joined: 05 Dec 2009 |
| Posts: 16 |
|
|
|
 |
| I think its made by KRAL, the gamo trigger mods should work |
|
_________________ fwiw joe |
|
 |
 |
|
|
|  |  |  | | | |  |  |
 |  | | | |  |  |  |  | |  | |  |  |  |
Posted: Sat Jan 23, 2010 11:01 pm |
|
|
| donec |
| Senior Member |

|
 |
| Joined: 19 Dec 2009 |
| Posts: 836 |
| Location: central Texas Pflugerville area |
|
|
 |
| joek wrote: |
| I think its made by KRAL, the gamo trigger mods should work |
I think the trigger is too good to mess with. |
|
|
 |
 |
|
|
|  |  |  | | | |  |  |
 |  | | | |  |  |  |  | |  | |  |  |  |
Posted: Sun Jan 24, 2010 2:16 am |
|
|
| kanyon |
| Silver Status Member |

|
 |
| Joined: 09 Aug 2008 |
| Posts: 1582 |
| Location: New Zealand |
|
|
 |
| joek wrote: |
| I think its made by KRAL, the gamo trigger mods should work |
They do look like Krals....The GRT/GTX trigger will not fit
Kral have made there sear wider from 3mm to 3.5mm
so it will not fit in the slot on the GRT trigger anymore..
yer can thin the sear down...
Pete |
|
|
 |
 |
|
|
|  |  |  | | | |  |  |
 |  | | | |  |  |  |  | Accuair Force 1100 |  | |  |  |  |
Air Gun Home Forum Index » Rifles
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
|
All times are GMT - 5 Hours
Page 1 of 1
|
|
|
|
|  |  |  | | | |  |  |
Note: If you are seeing "Please enter your username and password to log in." Your browser cookies have been reset
or you need to register to access the topic in question. Use the 'Register' button near the top left of this page.
|