Click Here for AirGunHome.com Main Page
Argentina Australia Belgium Canada Chile Denmark France Germany Greece India
Italy Mexico New Zealand Netherlands Norway Russian Federation South Africa Spain Turkey United Kingdom United States
AirGunHome.com: THE Worldwide Airgun Forum


AirGunSeals.com Main Page Link
Air Gun Home Forum Index Register FAQ Memberlist Search

Air Gun Home Forum Index » Airgun Smithing » 2240 Valve Retention Question Goto page 1, 2  Next
Post new topic  Reply to topic View previous topic :: View next topic 
2240 Valve Retention Question 
PostPosted: Mon Mar 08, 2010 8:36 pm Reply with quote
Mark5043
Silver Status Member
Silver Status Member
Joined: 12 Apr 2009
Posts: 1379
I plan on modding the valve on my 2300KT when it gets here from the custom shop.After studying some of the valve mods,I noticed that some guys are drilling,and tapping the C02 tube on both sides,in order to have 3 set screws holding the valve in place,as a safety precaution,instead of just the one factory location.Is this really necessary?Granted I wouldn't want a modded valve becoming part of my forehead,but it seems like overkill.It seems the valve would have to shear off the set screw,the hammer pin,and the rear,end cap screw in order for the assembly to exit the rear of the gun if a failure occurred.Is there any documented case of this happening? Huh?

_________________
View user's profile Send private message
 
PostPosted: Mon Mar 08, 2010 9:39 pm Reply with quote
Mark5043
Silver Status Member
Silver Status Member
Joined: 12 Apr 2009
Posts: 1379
Okay I found out that the particular mod is only for an HPA valve,and I don't need the mod for Co2.............. Rolling Eyes

_________________
View user's profile Send private message
 
PostPosted: Mon Mar 08, 2010 10:48 pm Reply with quote
kanyon
Silver Status Member
Silver Status Member
Joined: 09 Aug 2008
Posts: 1582
Location: New Zealand
It also use the port to locate/hold it at the top..
as well as the silly little bolt on the bottom..

Pete
View user's profile Send private message MSN Messenger
 
PostPosted: Tue Mar 09, 2010 12:20 am Reply with quote
Mark5043
Silver Status Member
Silver Status Member
Joined: 12 Apr 2009
Posts: 1379
kanyon wrote:
It also use the port to locate/hold it at the top..
as well as the silly little bolt on the bottom..

Pete
Good call....I'll have to remember this mod if i do a HPA conversion in the future.Now I can see why the mod is done.HPA,and a faulty valve retention would be no joke at all.

_________________
View user's profile Send private message
 
PostPosted: Tue Mar 09, 2010 2:30 pm Reply with quote
Jaxom
Senior Member
Senior Member
Joined: 06 Aug 2008
Posts: 927
One of the reasons this is, most...like myself swap out the stock 22xx valve for one from a discovery. The discovery valve being used for both Co2 and HPA has three mounting screws.

_________________
.22 2300kt Crosman Custom
View user's profile Send private message
 
PostPosted: Tue Mar 09, 2010 2:36 pm Reply with quote
oddtodd
Silver Status Member
Silver Status Member
Joined: 30 Dec 2008
Posts: 2029
Location: Richmond, IN USA
One thing that nobody mentioned is that because the 2240 is roll-stamped on that particular area it makes it too weak to hold HPA. You have to connect it some other way.

_________________
Airguns: Two starlings talking "Larry, did you hear that? Larry?? LARRY!!!!"
View user's profile Send private message Yahoo Messenger
 
PostPosted: Tue Mar 09, 2010 4:12 pm Reply with quote
packrat
Senior Member
Senior Member
Joined: 16 Nov 2009
Posts: 882
Location: Out in the woods...Ellabell, GA.
Like I answered this same post on another forum....if you get a highly modified CO2 gun, I'd certainly recommend pinning the valve...better safe than sorry..My 2250, using the little 12 gr cartidges came from the builder with valve pinned on one side, and I know he's way more knowledgable on these guns than I am.

_________________
HEY !! This getting old thing is NOT for sissies...
View user's profile Send private message Visit poster's website
 
PostPosted: Tue Mar 09, 2010 10:02 pm Reply with quote
kanyon
Silver Status Member
Silver Status Member
Joined: 09 Aug 2008
Posts: 1582
Location: New Zealand
oddtodd wrote:
One thing that nobody mentioned is that because the 2240 is roll-stamped on that particular area it makes it too weak to hold HPA. You have to connect it some other way.


This works....





View user's profile Send private message MSN Messenger
 
PostPosted: Tue Mar 09, 2010 10:39 pm Reply with quote
Mark5043
Silver Status Member
Silver Status Member
Joined: 12 Apr 2009
Posts: 1379
packrat wrote:
Like I answered this same post on another forum....if you get a highly modified CO2 gun, I'd certainly recommend pinning the valve...better safe than sorry..My 2250, using the little 12 gr cartidges came from the builder with valve pinned on one side, and I know he's way more knowledgable on these guns than I am.
I think your right here Pack...safety is the best bet..... Wink

_________________
View user's profile Send private message
 
PostPosted: Wed Mar 10, 2010 8:11 am Reply with quote
oddtodd
Silver Status Member
Silver Status Member
Joined: 30 Dec 2008
Posts: 2029
Location: Richmond, IN USA
kanyon wrote:
oddtodd wrote:
One thing that nobody mentioned is that because the 2240 is roll-stamped on that particular area it makes it too weak to hold HPA. You have to connect it some other way.


This works....







That's just pretty kanyon.

_________________
Airguns: Two starlings talking "Larry, did you hear that? Larry?? LARRY!!!!"
View user's profile Send private message Yahoo Messenger
 
PostPosted: Wed Mar 10, 2010 12:16 pm Reply with quote
Mark5043
Silver Status Member
Silver Status Member
Joined: 12 Apr 2009
Posts: 1379
What he said

_________________
View user's profile Send private message
 
PostPosted: Thu Mar 11, 2010 1:43 pm Reply with quote
rsterne
Moderator
Moderator
Joined: 15 Jan 2008
Posts: 2998
Location: Coalmont, BC
A stock 22XX valve is located only by the single 6-40 screw at the bottom.... If that fails, the valve can and will slide back partially or completely shearing the tiny 4-48 breech screw that is under the bolt.... Yes, there are documented cases of this happening on CO2 bulk fills.... If you think it's hard to get out normally, just imagine it half sheared through and bent over.... Rolling Eyes

Crosman 22XX guns are NOT designed to have the tube pressurized.... The sealing surface between the powerlet and the valve is about 0.2" OD at most.... that works out to 0.03 sq.in. and even at 120*F (1900 psi) that only results in an end force of about 60 lbs.... In order to bulk fill the tube, you need to seal the valve to the tube with an O-ring and the ID of the tube is 0.75".... That works out to an area of 0.442 sq.in..... and an end load on the valve of about 840 lbs. at 120*F on CO2.... 14 times as much load.... Shocked

While it is unlikely that the valve would be dislodged with enough force after shearing the 6-40 valve screw and the 4-48 breech screw to still have enough momentum to slam the hammer back into the rear end plug with enough force to shear off the two 8-32 screws that retain it.... you would sure have a heck of a time taking the mess apart after you change your shorts.... Laughing

The roll stamp issue is a separate one.... From what I have seen the 2240 and 2260 suffer from this, while the 2250 roll stamp is short enough to be in the unpressurized area behind the front trigger screw, even with a Disco length valve front end.... MuzzleMack products (yourdaddyjoe) makes an extended valve front end so that the roll stamp area is unpressurized in any 22XX tube.... You still need to mount the valve properly, however, to avoid the screws failing and ruining your day....

Bob

_________________
Dominion Marksman Silver Shield - 5890 x 6000 in 1976, and downhill ever since!
Airsonal: Too many to count!
View user's profile Send private message
 
PostPosted: Thu Mar 11, 2010 10:12 pm Reply with quote
Mark5043
Silver Status Member
Silver Status Member
Joined: 12 Apr 2009
Posts: 1379
Thanks for all the info here guys...it's nice to hear from the pro's before I start tinkering.Oh by the way..welcome back Bob! Mr. Green

_________________
View user's profile Send private message
 
PostPosted: Fri Mar 12, 2010 12:02 am Reply with quote
yourdaddyjoe
Supporting Member
Supporting Member
Joined: 26 May 2008
Posts: 4027
Location: Tatorville, USA
Hey Mark,

Is the 2300kt laser etched with the safety info. like the the 2400 Crosman Custom Shop guns? No Safety Info. Roll stamp on them...

Just one more reason to start out with the Custom Shop gun if your going to HPA it later...

_________________

Say "NO" to BB Gun Wars... Quid Pro Quo Rule: An eye for an eye...
www.HPASports.com www.Facebook.com/hpasports
View user's profile Send private message Visit poster's website
 
PostPosted: Fri Mar 12, 2010 9:51 am Reply with quote
Mark5043
Silver Status Member
Silver Status Member
Joined: 12 Apr 2009
Posts: 1379
yourdaddyjoe wrote:
Hey Mark,

Is the 2300kt laser etched with the safety info. like the the 2400 Crosman Custom Shop guns? No Safety Info. Roll stamp on them...

Just one more reason to start out with the Custom Shop gun if your going to HPA it later...
Yes Sir....it is........ Mr. Green

_________________
View user's profile Send private message
2240 Valve Retention Question 
  Air Gun Home Forum Index » Airgun Smithing
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
All times are GMT - 5 Hours  
Page 1 of 2  
Goto page 1, 2  Next
  
  
 Post new topic  Reply to topic  

Note: If you are seeing "Please enter your username and password to log in." Your browser cookies have been reset
or you need to register to access the topic in question. Use the 'Register' button near the top left of this page.


Click Here for AirGunHome.com Main Page


Powered by phpBB © 2001-2004 phpBB Group
Partial Styling Supplied by Vjacheslav Trushkin Themes Database.