 |  | | | |  | |  |  | Help!.. I have a 22xx and... |  | |  |  | |
 Posted: Thu May 14, 2009 2:17 am |
 |
|
| Storck-42 |
| Member |
|
|
| Joined: 25 Sep 2008 |
| Posts: 45 |
| Location: California |
|
|
|
.. every so many shots, maybe 3rd, maybe 5th, maybe 10th one happens where the shot is very weak , just barely strong enough to spit the pellet out of the barrel. When it does it, it might continue for 2 or 3 shots then return to normal  The valve and hammer assy is stock. I do have a power adjuster on it though.
Any thoughts on this?
TIA |
|
|
|
|
|
|
| |  |  | | | |  |  |
| | | | | | | | | | | | | | |
| Posted: Thu May 14, 2009 3:13 am |
|
|
| Brutuz |
| Senior Member |
|
|
| Joined: 12 Jan 2009 |
| Posts: 504 |
|
|
|
|
| Do you apply a drop of pellgunoil on the powerlet before inserting it? |
|
_________________
Crosman [1300 1322 1377 1377c 1389 2289G Mark II SSP250 2300KT 2400KT ]
Sheridan [HB20]
Haenel [III 284]
SMK [XS78 Deluxish]
My vids on Youtube |
|
|
|
|
|
| | | | | | | | |
| | | | | | | | | | | | | | |
| Posted: Thu May 14, 2009 3:18 am |
|
|
| yourdaddyjoe |
| Supporting Member |
 |
|
| Joined: 26 May 2008 |
| Posts: 4027 |
| Location: Tatorville, USA |
|
|
|
 Sticky valve steem... |
|
|
|
|
|
|
| | | | | | | | |
| | | | | | | | | | | | | | |
| Posted: Thu May 14, 2009 3:45 am |
|
|
| Storck-42 |
| Member |
|
|
| Joined: 25 Sep 2008 |
| Posts: 45 |
| Location: California |
|
|
|
| I put a small drop of Transmission fluid on each powerlet. |
|
|
|
|
|
|
| | | | | | | | |
| | | | | | | | | | | | | | |
| Posted: Thu May 14, 2009 5:44 am |
|
|
| Brutuz |
| Senior Member |
|
|
| Joined: 12 Jan 2009 |
| Posts: 504 |
|
|
|
|
Try 3 powerlets without a drop of oil, maybe there's to much oil inside now?
Maybe the oil you've been using is to thick? |
|
_________________
Crosman [1300 1322 1377 1377c 1389 2289G Mark II SSP250 2300KT 2400KT ]
Sheridan [HB20]
Haenel [III 284]
SMK [XS78 Deluxish]
My vids on Youtube |
|
|
|
|
|
| | | | | | | | |
| | | | | | | | | | | | | | |
| Posted: Thu May 14, 2009 10:00 am |
|
|
| yourdaddyjoe |
| Supporting Member |
|
|
| Joined: 26 May 2008 |
| Posts: 4027 |
| Location: Tatorville, USA |
|
|
|
| If you are in my neck of the woods... Stop by... and I will look at it... |
|
|
|
|
|
|
| | | | | | | | |
| | | | | | | | | | | | | | |
| Posted: Thu May 14, 2009 3:07 pm |
|
|
| fritz |
| Silver Status Member |
 |
|
| Joined: 25 Nov 2008 |
| Posts: 2444 |
| Location: New Jersey- outside of Philadelphia |
|
|
|
Could also be your rate of fire. If it's too quick the parts in your gun can cool off too much and cause the co2 to not expand fully.
Is your breach seal good? Transfer port? Something could be wiggling loose and operating the action could set it back in resulting in good shots. |
|
_________________
"I never set out to be wierd, it was always everyone else who called me it" -Frank Zappa
Speed is impressive, accuracy is deadly.
It's not that I'm not a people person, it's just that I'm not a stupid people person. |
|
|
|
|
|
| | | | | | | | |
| | | | | | | | | | | | | | |
| Posted: Thu May 14, 2009 4:43 pm |
|
|
| Slavia |
| Moderator |
 |
|
| Joined: 31 Mar 2008 |
| Posts: 4382 |
| Location: Waseca, Minnesota, USA |
|
|
|
| I would vote for the sticking valve stem. I don't think you can load and fire a 22XX fast enough to cool it down that much. Reduced power,yes. Pellet barely coming out, probably not. |
|
_________________
 ¡Listo! ¡Apunte! ¡Fuego! |
|
|
|
|
|
| | | | | | | | |
Note: If you are seeing "Please enter your username and password to log in." Your browser cookies have been reset
or you need to register to access the topic in question. Use the 'Register' button near the top left of this page.
|
