 |  | | | |  |  |  |  | FrankG CustomQB Project |  | |  |  |  |
Posted: Fri Jan 23, 2009 6:07 pm |
|
|
| FrankG |
| Member |

|
 |
| Joined: 18 Jan 2009 |
| Posts: 12 |
|
|
|
 |
|
|
 |
 |
|
|
|  |  |  | | | |  |  |
 |  | | | |  |  |  |  | |  | |  |  |  |
Posted: Fri Jan 23, 2009 7:49 pm |
|
|
| thepaladin |
| Senior Member |

 |
 |
| Joined: 12 Dec 2007 |
| Posts: 930 |
| Location: TN USA |
|
|
 |
|
_________________ "All that is necessary for the triumph of evil is that good men do nothing." (Edmund Burke) |
|
 |
 |
|
|
|  |  |  | | | |  |  |
 |  | | | |  |  |  |  | |  | |  |  |  |
Posted: Fri Jan 23, 2009 11:06 pm |
|
|
| AirGunEric |
| Site Admin |

 |
 |
| Joined: 20 Jan 2007 |
| Posts: 6930 |
| Location: "Out There" |
|
|
 |
| You added that lower extension right on to the existing stock or made another stock entirely? (I can't make out the back end very well as it's a bit dark in the picture). |
|
|
 |
 |
|
|
|  |  |  | | | |  |  |
 |  | | | |  |  |  |  | re |  | |  |  |  |
Posted: Sat Jan 24, 2009 8:26 am |
|
|
| FrankG |
| Member |

|
 |
| Joined: 18 Jan 2009 |
| Posts: 12 |
|
|
|
 |
Hi Eric,
It's a complete new stock I made it all by myself...took me a couple of days to carve it...the inlet was the thing that took me a bit more time.but the inlet of the QB is pretty simple.It's even me that have lumber the wood for it...
FrankG |
|
|
 |
 |
|
|
|  |  |  | | | |  |  |
 |  | | | |  |  |  |  | |  | |  |  |  |
Posted: Sat Jan 24, 2009 8:44 am |
|
|
| FrankG |
| Member |

|
 |
| Joined: 18 Jan 2009 |
| Posts: 12 |
|
|
|
 |
| I will try to take some other picture today so you can see it from every angle...The tools I did use was: Rooter with a 3/4 round bit,Sanding tools,Chisel,Table saw,Band saw.I did make my design on cardboard first.The stock fit like a glove on me(it was made by me and for me) |
|
|
 |
 |
|
|
|  |  |  | | | |  |  |
 |  | | | |  |  |  |  | |  | |  |  |  |
Posted: Sat Jan 24, 2009 12:16 pm |
|
|
| FrankG |
| Member |

|
 |
| Joined: 18 Jan 2009 |
| Posts: 12 |
|
|
|
 |
|
|
 |
 |
|
|
|  |  |  | | | |  |  |
Note: If you are seeing "Please enter your username and password to log in." Your browser cookies have been reset
or you need to register to access the topic in question. Use the 'Register' button near the top left of this page.
|