 |  | | | |  |  |  |  | Stocks Broken In Transit---Let's Stop It Now!! |  | |  |  |  |
Posted: Sat Aug 30, 2008 8:46 am |
|
|
| Ed Krzynowek |
| Member |

|
 |
| Joined: 24 Aug 2008 |
| Posts: 17 |
|
|
|
 |
I just got another one yesterday--basically a brand new, German-made, spring-piston airgun. UPS was the carrier. Don't jump to conclusions. There's at least a good possibility it could have been prevented.
An edge slam (or hard drop on the 'edge' or 'height' of the box) is usually what causes the infamous pistol grip break, just like this one has. There is no other apparent damage at this point. That is, it's not very likely that damage only at the pistol grip will be caused by an end-drop, unless it's very, very-extreme in nature. There would usuallly be other signs of damage in that case. I've posted about it before.
So, before anyone gets started in a false direction, think about this, first:
This is the exact same kind of breakage that occurs if you slam fire a barrel cocker, or let go of the barrel with your cocking hand while it's partially-cocked, so that the barrel slams home. Don't do either of those things to your springer! If you obey those rules, your pistol grip won't break as a result.
<b>Therefore, you don't need to send the stock in receiver as two separate pieces to prevent breakage, anymore than you need to carry them that way in the field, or cock and fire them that way.</b>
Instead, you need to fully-support the rifle at its midsection.
For a good example of how to do that, go look at your factory packing from Beeman and others: There is not only a support at each end, BUT THERE'S ONE MORE SUPPORT IN THE MIDDLE THAT PREVENTS ANY UP OR DOWN MOVEMENT OF THAT PART OF THE STOCK. That's why that piece of cardboard is there, and why that lightweight mailing box almost always delvers a stock that is NOT broken at the grip even if the box is dropped fairly-hard.
THAT CARDBOARD SUPPORT is what you need to duplicate...
...with cardboard, foam, bubble wrap, or a towel, or something. That is, something that's specifically designed to prevent any movement in the downward direction if it gets dropped horizontally, with the trigger side aimed down at the ground (or any point of impact). A drop in that direction duplicates the same huge intertial force to the stock that you get with a slam fire or slipped cocking lever--thus the duplication in the exact area and exact appearance of breakage.
If you support the stock well underneath the trigger guard where these breaks occur, so that a drop in that direction doesn't allow the heavy midsection of the rifle and stock 'to try to outrace the two ends to the ground', it won't flex and therefore it won't break, (unless the slam force was so great it never had a chance in the first place).
Note: A rifle case that is heavy enough with foam to keep the entire rifle dead calm still, clammed in-between a thick foam sandwich with plenty of foam all around the perimeter of the rifle, will accomplish the same protection if the case gets dropped 'trigger-down'.
Of the last two hundred air rifles I've received, I've only had 3 break in-transit to me IIRC. No stock I've shipped has ever been broken on its way back to the owner, because of the way I pack---and I guess the delivery truck wheels missed the boxes, too.
Of those 3 that broke on the way here, I've never had a stock that was shipped as I described above get broken, except for one that was in a case that was so small, the two ends of the rifle (muzzle and bottom tip of buttstock) rested firmly and directly on the hard perimeter of the rifle case. In that one instance, the packing method really didn't fit the above decsription, because there was no foam around the perimeter of the rifle to protect it. Thus, when it got dropped, the two ends were basically resting on hard ground---so that even a minute flex at the midsection allowed the partially-dry-rotted wood to break at the customized, thin pistol grip.
Please note, the above packing method still doesn't cover situations where the carrier flexes the box hard to either side, as if using it for a flat crowbar. In fact, damage from that scenario could happen even if you DO send the stock in a separate box.
Like I said, I'll be posting a 'how-to' tutorial with pictures later. For now, please think about the above, where this type of break occurs, and thus where the support needs to be. |
|
_________________ Happy Shooting,
Ed |
|
 |
 |
|
|
|  |  |  | | | |  |  |
 |  | | | |  |  |  |  | |  | |  |  |  |
Posted: Sat Aug 30, 2008 2:56 pm |
|
|
| AirGunEric |
| Site Admin |

 |
 |
| Joined: 20 Jan 2007 |
| Posts: 6931 |
| Location: "Out There" |
|
|
 |
| There are a number of manufacturers that do not package guns properly straight from the factory. The Chinese companies are the worst for it, but I've caught a couple of Crosman's with the same problem and some German guns where a bit more packaging on the end of the barrel and the stock would certainly help avoid damage. Not sure why so many companies seem to try and save a few pennies on packaging materials... |
|
|
 |
 |
|
|
|  |  |  | | | |  |  |
 |  | | | |  |  |  |  | |  | |  |  |  |
Posted: Sun Aug 31, 2008 1:03 am |
|
|
| yourdaddyjoe |
| Supporting Member |

 |
 |
| Joined: 26 May 2008 |
| Posts: 4027 |
| Location: Tatorville, USA |
|
|
 |
The Brown Bomber strikes again
 |
|
|
 |
 |
|
|
|  |  |  | | | |  |  |
Note: If you are seeing "Please enter your username and password to log in." Your browser cookies have been reset
or you need to register to access the topic in question. Use the 'Register' button near the top left of this page.
|