Click Here for AirGunHome.com Main Page
Argentina Australia Belgium Canada Chile Denmark France Germany Greece India
Italy Mexico New Zealand Netherlands Norway Russian Federation South Africa Spain Turkey United Kingdom United States
AirGunHome.com: THE Worldwide Airgun Forum


AirGunSeals.com Main Page Link
Air Gun Home Forum Index Register FAQ Memberlist Search

Air Gun Home Forum Index » Rifles » .25 cal Disco Hammer Preload Testing
Post new topic  Reply to topic View previous topic :: View next topic 
.25 cal Disco Hammer Preload Testing 
PostPosted: Mon Jan 26, 2015 4:58 pm Reply with quote
rsterne
Moderator
Moderator
Joined: 15 Jan 2008
Posts: 2998
Location: Coalmont, BC
The last time I was working on my .25 cal Disco I replaced the barrel with a .25 ACP liner from TJ's to specialize it for cast bullets, and replaced the tapered MRod poppet with one made from PEEK.... This gun has a pretty fancy valve in it, using a 2-piece design as in the photo below.... The valve is secured with three high tensile 10-32 screws to allow safe fills to 3000 psi....



The valve has full boresize porting and a 9/32" throat, the only restriction below 0.250" is the barrel port (an oblong port the equivalent of 0.240") and a slender probe on the bolt.... I recently made a 2900 psi inline regulator, so now it is easy to tether any gun at that pressure to check out how it responds to changes in hammer spring preload.... That way I can determine if I have enough power in the hammer to max. out the performance at 2900 psi.... I ran those tests today, and here are the results with three weights of cast bullets.... 0.5 Turns past flush on the adjuster was the maximum preload I can use and still cock the gun without coil bind on the QB hammer spring....



As you can see, I have just enough hammer strike available to max. out the velocity of the gun, as shown by the plateaus on the left of the graph.... With the 58.8 gr. Mr. Hollowpoint bullets, the gun peaked at 960 fps (120 FPE), and achieved 115 FPE with my 50.6 gr. Bob's Boattails and 111 FPE with 46.4 gr. Hollowpoint version of the .25 ACP bullet.... These represent the range of bullet weights practical for this gun at this power level.... which is 5 times the FPE of a stock Disco....

I dropped the hammer spring preload back to 1 Turn out from flush, and the gun was shooting consistently at 960 fps (104 FPE) with my BBT's, at just under 1.0 FPE/CI efficiency.... Filling to 2900 psi and dropping the gun off the tether allows three shot of 960-966-956 (a 1% ES) before the velocity drops off.... That's a 3 shot average of 961 fps (104 FPE), and I can drop the gun back to about 97 FPE and get 5 good shots within a 4% ES.... From looking at it, you basically can't tell the gun isn't a stock Disco.... It does, however, have a bit of a bark!....

Bob

_________________
Dominion Marksman Silver Shield - 5890 x 6000 in 1976, and downhill ever since!
Airsonal: Too many to count!
View user's profile Send private message
.25 cal Disco Hammer Preload Testing 
  Air Gun Home Forum Index » Rifles
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
All times are GMT - 5 Hours  
Page 1 of 1  

  
  
 Post new topic  Reply to topic  

Note: If you are seeing "Please enter your username and password to log in." Your browser cookies have been reset
or you need to register to access the topic in question. Use the 'Register' button near the top left of this page.


Click Here for AirGunHome.com Main Page


Powered by phpBB © 2001-2004 phpBB Group
Partial Styling Supplied by Vjacheslav Trushkin Themes Database.