| | | | | | | | | how thick should brass pivot washers | | | | | |
|
|
|
I would have thought thick enough to fill the gap with a bit of lube applied without being tight, then adjust the with the screw to get a smooth pivot without any side movement.
Al
it worked out ... |
|
|
|
|
|
| | | | | | | | |
| | | | | | | | | anyone know the dimensions | | | | | |
|
|
|
i finally got 'em
0.70" OD
0.35" ID
0.063" thick
i had to do a lot of fine fitting by way of file and lathe... |
|
|
|
|
|
| | | | | | | | |
| | | | | | | | | how thick should brass pivot washers | | | | | |
|
|
|
I would have thought thick enough to fill the gap with a bit of lube applied without being tight, then adjust the with the screw to get a smooth pivot without any side movement.
Al
sounds good.. ... |
|
|
|
|
|
| | | | | | | | |
| | | | | | | | | arrggggg | | | | | |
|
|
|
thanks again. I think im going to return it and hold off for a marauder
sounds reasonable... |
|
|
|
|
|
| | | | | | | | |
| | | | | | | | | best brand pellet gun for under $200? | | | | | |
|
|
|
purchasing used, you could find a used higher quality beeman, RWS or HW
in 177 that will more than meet your needs.
IF, you do decide to go to a used gun, be sure to look it over closely, note any ... |
|
|
|
|
|
| | | | | | | | |
| | | | | | | | | let me change the question. | | | | | |
|
|
|
Measure what you've got for ID and OD- the thickness is going to depend on what you are trying to "correct". Typically, brass washers are done for these rifles in 0.55", 0.60" and ... |
|
|
|
|
|
| | | | | | | | |
| | | | | | | | | let me change the question. | | | | | |
|
|
|
of an earlier post.
anyone know what sized brass/copper washers to replace the factory plastic pivot washers in a Benjamin NP Trail.
i know i can get the standard plastic ones from crosman, but ... |
|
|
|
|
|
| | | | | | | | |
| | | | | | | | | Rear Tank Airguns | | | | | |
|
|
|
One of the issues with a rear-tank setup is positioning the rifle. For example, the AirForce products can be a bit of a pain- the tank becomes like an overly-wide stock. While I own a Condor and like ... |
|
|
|
|
|
| | | | | | | | |
| | | | | | | | | Low cost PCP air guns. | | | | | |
|
|
|
You can do that with a QB78 by just adding a bulk-fill fitting and pumping to about 1300-1500 psi.... Adjust the fill and refill pressure to give you the bell-curve (ES) you want.... A stock gun will ... |
|
|
|
|
|
| | | | | | | | |
| | | | | | | | | Is this A good Rifle and scope combo? | | | | | |
|
|
|
if you are an experienced air gunner, it may be ok...but if this is your first magnum air rifle, it WILL take some getting used to.
FWIW, i would look to a medium range powered HW or RWS. they cost ... |
|
|
|
|
|
| | | | | | | | |
| | | | | | | | | best pellets for the money | | | | | |
|
|
|
JSB's, H&N/Beeman Barracudas...in springers and PCP rifles.
lots of FPE and accurate to the extreme in many, if not most, cases of long distance shooting.
most of my shooting is at ranges th ... |
|
|
|
|
|
| | | | | | | | |
| | | | | | | | | HW 90 or Theoben Eliminator? | | | | | |
|
|
|
i doubt it...i don't recall hearing about ANY springer that will do that
IMO...i think i might opt for the 22 as there is very little difference in the 22 and the 25 in FPE; 22 ammo is more readily ... |
|
|
|
|
|
| | | | | | | | |
Page 1 of 17 |
Goto page 1, 2, 3 ... 15, 16, 17 Next All times are GMT - 5 Hours |
Note: If you are seeing "Please enter your username and password to log in." Your browser cookies have been reset
or you need to register to access the topic in question. Use the 'Register' button near the top left of this page.
|